Scenario You have recently joined the team at A&L, an engineering firm with a broad portfolio. A&L has recently been hired to help plan a supply drop following a natural disaster. Due to conditions on the ground, the supply drop will be done from the air. Your supervisor has asked you to use that information, as well as your knowledge of kinematics, to create a supply drop plan detailing how far the payload should be from the drop site when it is delivered. Additionally, due to adverse conditions in the area, your supervisor has asked you to prepare for two contingencies. Directions Don't use plagiarized sources. Get Your Custom Essay on
Describe the motion of an object in one and two dimensions Assignment | Professional Essay Writers
Just from $13/Page
Construct a diagram that describes the horizontal and vertical motion of the payload. Your diagram should visually represent the initial velocity and height of the payload as it approaches the drop site. To create the diagrams, you may use drawing tools, or you may photograph or screenshot a drawing of your own. This diagram should include the following elements: Supply Drop Plan |

**Competency**

In this project, you will demonstrate your mastery of the following competency:

- Describe the motion of an object in one and two dimensions

**Scenario**

You have recently joined the team at A&L, an engineering firm with a broad portfolio. A&L has recently been hired to help plan a supply drop following a natural disaster. Due to conditions on the ground, the supply drop will be done from the air. Your supervisor has asked you to use that information, as well as your knowledge of kinematics, to create a supply drop plan detailing how far the payload should be from the drop site when it is delivered. Additionally, due to adverse conditions in the area, your supervisor has asked you to prepare for two contingencies.

**Directions**

The plane carrying the supplies will be cruising at a constant velocity of 250 miles per hour relative to the ground and at a height of 2,650 meters above the target site. Using this information, create a **supply drop plan** including all required information and calculations outlined below. As you are completing your supply drop plan, remember that correct SI units are a required component of your calculations and descriptions.

**Construct a diagram that describes the horizontal and vertical motion of the payload.**Your diagram should visually represent the initial velocity and height of the payload as it approaches the drop site. To create the diagrams, you may use drawing tools, or you may photograph or screenshot a drawing of your own. This diagram should include the following elements:- The initial velocity of the payload
- The initial height of the payload
- Horizontal distance to the drop site

- Using your understanding of kinematic equations and the given variables in the scenario,
**calculate the horizontal and vertical motion of the payload**to ensure it arrives at the drop site. In your calculations, account for both the horizontal and vertical motion of the payload. Your calculations should address the following:- Initial velocity of the payload when launched
- The velocity of the payload when it hits the ground

- Following your calculations,
**describe the equations used in calculating the vertical and horizontal motion of an object.**In your descriptions, address the following:**What is the relationship between vertical and horizontal motion in kinematics equations?**- How did you analyze the vertical motion of the payload in your solution?
- How did you analyze the horizontal motion of the payload in your solution?
- What other kinematics principles did you consider in analyzing the motion of the payload?

- Following your initial calculations, your supervisor has asked you to consider two additional scenarios. For both scenarios listed below,
**adapt your diagrams and descriptions to respond to changing variables**. Create a diagram describing the horizontal and vertical motion of the payload in order to reach the drop site, and then use your understanding of kinematic equations to describe how these changes would affect calculations for the payload. The two additional scenarios are described below:- In order to prepare pilots for changes in condition, you have been asked to model supply drops by a plane flying into a headwind. For this scenario, you will choose your own location. Use a resource such as the National Weather Serviceto select a location. Be sure to name the location and use the wind speed in the area to determine the headwind for the plane. For this scenario, consider the plane’s speed and the height above the drop site to be the same as the first scenario: a speed of 250 miles per hour relative to the ground and at a height of 2,650 meters above the target site.
- Due to historical difficulty in delivering supplies by plane, one of your colleagues has suggested you develop a catapult for slinging supplies to affected areas, similar to the electromagnetic lift catapults used to launch planes from aircraft carriers. This catapult is located at a fixed point 400 meters away and 50 meters below the target site. The catapult is capable of launching the payload at 67 meters per second and an initial launch angle of 50 degrees. Using your knowledge of kinematics equations, determine whether this would be sufficient to deliver the payload to the drop site.

- Once you have completed your adjusted diagrams and equations,
**describe the effects of changing variables on kinematic equations**. These descriptions should reflect the different motions and considerations made for the modifications you considered in the previous step. In your descriptions, be sure to address the following:- How did the changing variables affect the vertical and horizontal motion of the payload?
- What adjustments to delivery would need to be made to account for these changing variables?

**What to Submit**

To complete this project, you must submit the following:

**Supply Drop Plan**

Your supply drop plan should include three diagrams depicting the vertical and horizontal motion of an object. Additionally, you should describe the equations used in your calculations and provide a written summary of the object’s motion in each scenario. Optionally, you may use the Supply Drop Template to help plan and organize your work.

**A&L Engineering**

**Supply Drop Plan**

**Instructions:** Respond to the prompts in the tables below and replace the text in brackets.

Create a diagram describing the horizontal and vertical motion of the payload. Remember that your diagram should visually represent the motion of the payload. |

Provide your calculations, including all relevant steps are included and your units are labeled. |

[Insert text here.]

Describe the components of the kinematics equations used in your initial calculations below. |

[Insert text here.]

Create a diagram showing the first modified scenario. Then adjust your initial calculations to incorporate the changing variables from the scenario and describe how these changed variables affect your calculations. |

[Insert text here.]

Create a diagram showing the second modified scenario. Then adjust your initial calculations to incorporate the changing variables from the scenario and describe how these changed variables affect your calculations. |

[Insert text here.]

Paper format

- 275 words per page
- 12 pt Arial/Times New Roman
- Double line spacing
- Any citation style (APA, MLA, Chicago/Turabian, Harvard)

Try it now!

How it works?

Follow these simple steps to get your paper done

Place your order

Fill in the order form and provide all details of your assignment.

Proceed with the payment

Choose the payment system that suits you most.

Receive the final file

Once your paper is ready, we will email it to you.